Macon Precision Machining LLC
Macon Precision Machining LLC

​

​

CONTACT US
  • Home
  • Our Products
    • John Deere Tractor Tools
    • DT 4366E TOOL
    • Polaris Fuel Cell Nipple
  • Services Provided
    • CNC & Manual Machining
    • Automotive & Cylinder Head
  • Contact Us
  • About Us
    • Shop Tour

Power Beyond Kit for John Deere Tractors

This kit is new, comes with all the pieces pictured.  With this kit you can run additional hydraulic valves for attachments such as a log splitter, forks, etc.  The Power Beyond housing is not a casting like you would get from John Deere.  Our housing is made of 1018 steel and was machined on a CNC mill to the same specifications as the housing from John Deere. Also, List of known tractors that the kit will work on: 3020 (1969 and newer); 4020 (1969 and newer); 4320; 4230; 30 Series Row Crop and 4WD 4030,4230,4430,4630; 40 Series Row Crop and 4WD 4040,4240,4440,4640,4840;50 Series Row Crop and 4WD 4050,4250,4450,4650,4850; 55 Series Row Crop; 60 Series Row Crop and 4WD; 70 Series Row 4WD.
If your tractor is not listed above, contact us before you buy to insure the Power Beyond Kit will work for your model of John Deere tractor.

$178.00
+$10.00 Priority Mail Shipping

 (Lower 48 States Only) 

Picture
$178.00 (plus shipping)

John Deere Front Tractor Weight Stud Bolts

Our front tractor weight bolts are machined to John Deere specifications stud bolts or screws that fit on the front of various John Deere tractors for attaching weights to.They are the same size and specs as JD part no. R27645 or R47645. They will come to you as seen with no finish or protective coating on them. John Deere tractors that the Front End Weight Stud Bolts will fit: 2510, 2520, 3010, 3020, 4010, 4020, 4320, 4520, 4620 and possibly others. You will receive 2 bolts (a pair).
Picture
$50.00 for the pair (plus shipping)

$50.00
+$8.45 Priority Mail shipping

(Lower 48 States Only)

JDH-42-2 Centering Pins

This specialty tool is used to center the steering meter pump. Our tool is made from the same measurements as the John Deere tool, JDH-42-2. Our tool is made from drill rod and machined in our shop. You will receive 2 pins and they will come to you as shown with no finish or protective coating.

$35.00
+$8.45 Priority Mail Shipping

(Lower 48 States Only) 


John Deere Clutch Alignment Tool

The clutch alignment tool or pilot tool works on 6 different tractors, the smaller end can be used on the 3000 series tractors and the larger end works on the 4000  series tractors.This one tool takes the  places of two separate tools. This tool works on the following tractors: 3010, 3020, 4000, 4010, 4020, and 4320.This tool was made from a solid pieces of 1¾” diameter 1018 cold rolled steel. It was machined on a CNC lathe according to the specifications found in “I&T Shop Service manual no. JD-49 (also the same drawing found in manual no. JD-53 and JD-203).  After being machined it was given a black finish.  Unlike similar tools made of plastic, our tool will last for years to come.

$65.00       
+$10.00 Priority Mail shipping

(Lower 48 States Only)    

Picture
$65.00 plus shipping

John Deere Clutch Adjusting Tool JDE-61

Our clutch adjusting tool was made from an 1/8th thick piece of 1018 steel that was machined on a CNC mill. It was made to the same specifications as the John Deere tool, JDE-61.  For use on the following JD tractors: 3010, 3020, 4000, 4010, 4020, 4320, 4520, 4620, and possibly others.
Picture
$55.00 plus shipping

$55.00
+$8.65 Priority Mail shipping

(Lower 48 States Only) 

SAVE $$$ - John Deere Clutch Tool Set

You get the clutch alignment tool and the clutch adjusting tool for one set
price.  Save $25.00 and  shipping cost when you purchase the set.
Picture
$95.00 (plus shipping)

$95.00
$10.00 Priority Mail shipping

(Lower 48 States Only) 


John Deere JDH-28 Rockshaft Valve Guide Installing Tool

This tool is used for assisting in the installation of rockshaft valves. Our tool was made from the same specifications as the original JDH-28 (pictured far left). You will be receiving the silver tool to the right.

$90.00
$9.45 Priority Mail shipping

(Lower 48 States Only) 

Picture
$90.00 (plus shipping)

John Deere Clutch Adjusting Tool JD-227

This clutch adjusting tool was made from a piece of 1018 steel that was machined on a CNC mill. It was made to the same specifications as the John Deere tool, JD-227.

$150.00
$9.65 Priority Mail shipping

(Lower 48 States Only) 

Picture
$150.00 (plus shipping)

John Deere JDH-3D Steering Valve Adjustment Tool

This one tool can be used on 6 different tractors for adjusting the steering valve.  A must have for any tractor mechanic that works on John Deere series tractors listed below (and possibly other models): 3020, 4000, 4020, 4320, 4520, and 4620.  This tool was made from solid piece of 1018 Cold Rolled Steel. It comes with two bolts and locking jam nuts as seen in the photos.  It was machined on a CNC mill from the same  specifications from an original tool, JDH-3D (replaces JDH-3C).
Picture

$95.00
$8.45 Priority Mail shipping
(Lower 48 States Only) 

Picture
$95.00 (plus shipping)

JDH-8 John Deere Rockshaft Valve Stop

For use on John Deere tractors, 3000 Series, 4000 Series and some 5000 Series. This tool was made from 1018 steel and machined on a CNC mill using the same specifications from an original OTC here at our shop.  The JDH-8 tool is used as a stop when using the JDH-11 rockshaft valve indicator (not included).
Picture
$75.00 (plus shipping)

$75.00
+$8.45 Priority Mail shipping
(Lower 48 States Only) 

JDT-4 Shift Blocker Spring & Ball Sleeve

This specialty tool is used to load springs and balls into low and high range synchronized blockers on transmission drive shafts of John Deere tractors.Our tool is made from the same specifications as the John Deere tool, JDT-4.It was made from a piece of 1018 steel and turned on a CNC lathe.After being machined it was given a black finish to prevent rusting. It is known to work on John Deere 3010, 3020, 4010, and 4020.  It could possibly be used on other 3000 series and 4000 series tractors.
Picture
$95.00 (plus shipping)

$95.00
$9.65 Priority Mail shipping

(Lower 48 States Only) 


JDH-15 John Deere Selective Control Adjusting Plate

For use on John Deere 3010, 4010, 3020 and 4020 tractors, 1968 and older..  This tool was made from 1018 steel and machined on a CNC mill using the same specifications from an original OTC tool here at our shop.  The JDH-15 tool is used as an adjusting plate for the selective control valve.  The plate comes as shown with the 5 bolts pictured.

$75.00
+$8.45 Priority Mail shipping
(Lower 48 States Only) 

JDH-15C John Deere Selective Control Adjusting Plate

For use on John Deere 1969 and newer 20 and 30 series tractors ( this includes models 3020, 4020, 4320, 4030, 4230, 4430, and 4630).  This tool was made from 1018 steel and machined on a CNC mill using the same specifications from an original OTC tool here at our shop.  The JDH-15C tool is used as an adjusting plate for the selective control valve.  The plate comes as shown with the 6 bolts pictured.
Picture
$115.00 (plus shipping)

$115.00
+$9.45 Priority Mail shipping
(Lower 48 States Only) 


JDT-15 Oil Seal Driver

For use on 4000 Series John Deere tractors.

$90.00
+$9.65 Priority Mail shipping
(Lower 48 States Only) 


JDH-16 Load Control Shaft Bushing Driver

 For use on 4000 Series John Deere tractors.

$50.00
+$9.65 Priority Mail shipping
(Lower 48 States Only) 

JDT-16 Oil Seal Driver

For use on 3000 Series John Deere tractors.

$90.00
+$8.00 Priority Mail shipping
(Lower 48 States Only) 


JDE-14 Vent Pump Idler Gear Bushing Driver

For use on 3000 and 4000 Series John Deere tractors.

$60.00
+$9.65 Priority Mail shipping
(Lower 48 States Only) 

Powered by Create your own unique website with customizable templates.